Kuraray RMS702-PVA Fibra para Refuerzo de Hormigón

Kuraray RMS702-PVA is a polyvinyl alcohol synthetic fibre supplied for reinforcement of concrete, shotcrete, and mortar. The fibre is produced as a cut monofilament; cut length, diameter or decitex, and surface finish are defined on the manufacturer’s technical data sheet and lot certificate. RMS702 is positioned within the high-modulus PVA fibre class because its production route includes drawing and heat-setting steps that align the polymer chain, increasing tensile strength and elastic modulus relative to lower-modulus PVA monofilaments. Under ASTM C1116/C1116-23, the material falls within Type III synthetic polymer fibres. Under EN 14889-2:2006, polymer fibres for structural or non-structural concrete are subject to initial type testing of geometry, tensile behaviour, alkali resistance, and influence on concrete properties. Representative peer-reviewed data for high-modulus Kuraray PVA fibres used in engineered cementitious composites report a density of 1.30 g/cm³, tensile strength in the range 1,560–1,620 MPa, elastic modulus of 41–43 GPa, and elongation at break near 6%. Independent published data specific to RMS702 is limited; the above values are class-representative and should be confirmed against the supplier’s initial type test certificate. RMS702 is intended for crack-width control, plastic shrinkage mitigation, post-crack toughness improvement, and, at higher addition rates, strain-hardening cementitious behaviour. It is not a direct substitute for primary steel reinforcement.

What Distinguishes the High-Modulus PVA Class from Polypropylene and Steel Fibres?

The primary technical distinction from polypropylene is the combination of elastic modulus and fibre–cement bond. Polypropylene fibres in concrete typically exhibit tensile strength below 700 MPa and elastic modulus below 10 GPa, whereas high-modulus PVA fibres can exceed 1,500 MPa tensile strength and 40 GPa elastic modulus. This reduces the fibre volume required to achieve a measurable post-crack residual load. The PVA surface is hydrophilic and wettable by cement pore solution; polypropylene is hydrophobic and depends on mechanical anchorage or surface deformation for bond. Lower-modulus PVA grades may exhibit tensile strength nearer 880 MPa and elastic modulus below 30 GPa; high-modulus grades such as RMS702 are drawn to increase molecular orientation, which raises tensile strength and modulus but lowers elongation. In comparison with steel fibres, PVA density is 1.30 g/cm³ versus approximately 7.85 g/cm³, lowering added dead load and eliminating surface rust staining. However the elastic modulus of high-modulus PVA remains roughly one-fifth to one-fourth that of steel at 200 GPa, so PVA fibres do not provide the same stiffness-driven crack restraint in hardened concrete. The substitution logic is therefore not volumetric: a direct one-to-one replacement of steel fibres with PVA is invalid without re-evaluating section behaviour. Batching and dispersion constraints become more severe as fibre length increases. Ready-mix operations using pan mixers, planetary mixers, or twin-shaft compulsory mixers with batch capacities between 0.5 m³ and 2.0 m³ generally require staged introduction of PVA monofilaments after the initial aggregate–water contact to reduce electrostatic clumping. High-aspect-ratio monofilaments with cut lengths from 6 mm to 12 mm may form visible balls at addition rates above 0.5 vol% if the fibre charge is introduced too rapidly or before the aggregate is fully wetted. Monofilaments of 18 mm or longer present greater dispersion control requirements. The low bulk density and hydrophilic surface of PVA cause moisture regain under ambient humidity. In automatic dosing systems, preconditioned fibre sacks should remain sealed until batching, and prolonged storage above 70% relative humidity can be problematic because moisture uptake alters screw-feeder mass flow and promotes filament clustering. Extension of mixing time beyond the plain-concrete reference cycle may be required to achieve uniform fibre distribution, but severe high-shear mixing should be controlled because excessive energy input can damage monofilaments and increase air entrapment.

Alkaline Hydrolysis Resistance and Interfacial Bond Mechanics

PVA fibres are selected for cementitious service because the polymer backbone remains stable in the pH 12.5–13.5 pore solution of hydrating portland cement. Unlike E-glass, the fibre does not rely on zirconia additions for alkali resistance, and unlike some cellulosic fibres, it does not undergo severe alkali-promoted strength loss at normal service temperatures. Bonding to the cement matrix is governed by two sequential mechanisms. A chemical bond arises from hydroxyl interactions at the fibre surface and from interactions with calcium-bearing hydration products; this bond can be strong enough that fibre rupture rather than pull-out becomes the controlling failure mode at certain embedment geometries. After debonding, a frictional sliding resistance is controlled by surface roughness, matrix density, and fibre diameter. High-modulus grades such as RMS702 combine tensile strength above 1,500 MPa, elastic modulus above 40 GPa, and elongation at break near 6%; the fibre can therefore bridge microcracks without immediate rupture, transferring stress across crack faces before pull-out. In ECC formulations using 2 vol% of similar Kuraray PVA fibre, this fibre–matrix combination is the basis for multiple-microcracking behaviour and tensile strain capacity above 3%. The same response is unlikely with low-modulus polymeric fibres because fibre rupture or pull-out occurs before substantial stress transfer, resulting in localized cracking rather than distributed microcracking.

Rheological Consequences in Low Water–Cementitious Matrices

In high-performance concrete with water-to-cementitious ratio below 0.40, the large specific surface area of fine PVA monofilaments increases yield stress and plastic viscosity. This effect is more pronounced than with steel or polypropylene macrofibres at equal mass dosage because PVA fibre counts per kilogram are high and the hydrophilic surface adsorbs free water. Mix design adjustments are therefore matrix-specific. A dosage of 0.5 vol% RMS702 may reduce slump-flow in self-compacting concrete unless a high-range water-reducing admixture is adjusted; the required admixture increment is influenced by cement type, supplementary cementitious materials, and aggregate fines. A universal dosage increment is not technically valid and should not be prescribed without trial batching. Air content should also be monitored after fibre addition because prolonged mixing can entrain air at the fibre–matrix interface. The fibres should be considered as part of the fine-particle and surface-area balance in concrete mixture proportioning, and the effects on workability should be established with a concrete rheometer, slump-flow cone, or standard slump test under ASTM C143/C143M or equivalent regional procedure. Table 1 lists representative fibre class values for concrete reinforcement. The values are collected from published fibre and composite literature; they are not a substitute for lot-specific RMS702 certificates because fibre geometry and surface finish alter mechanical performance.

Fibre class	Density (g/cm³)	Tensile strength (MPa)	Elastic modulus (GPa)	Elongation at break (%)	Surface character
High-modulus PVA	1.30	1,560–1,620	41–43	6	Hydrophilic
Lower-modulus PVA	1.30	880–1,000	25–30	7–10	Hydrophilic
Polypropylene	0.90–0.91	300–700	3.5–10	15–25	Hydrophobic
Steel	7.85	1,000–2,600	200	1–4	Not applicable
AR-glass	2.68	1,700–3,500	72	2–3	Hydrophilic

The table shows that RMS702-class PVA fibre does not match steel modulus, but it exceeds polypropylene modulus by a factor of approximately 4 to 10. The high count of PVA filaments per kilogram, resulting from the 1.30 g/cm³ density and fine diameter, supplies fine microcrack distribution; however the same high surface area can increase paste viscosity. In mix designs with water-to-cementitious ratio below 0.40, the addition of PVA fibre above 0.5 vol% commonly requires an increase in high-range water-reducing admixture, but the exact increment is matrix-specific and should be established by trial batching rather than prescribed generically.

When Post-Crack Residual Strength Governs Specification

Where project specifications impose post-crack flexural performance, testing is commonly conducted under ASTM C1609/C1609M-19a or EN 14651. Under ASTM C1609/C1609M, a third-point-loaded beam yields residual strength at net deflections of L/600 and L/150. PVA fibre dosage in the 0.5–2.0 vol% range can provide measurable residual strength; the exact residual load depends on fibre count, embedment length, matrix compressive strength, aggregate top size, and mixing energy. At fibre volume fractions of 0.5–2.0 vol%, residual strength increases with dosage, but the relationship is not always linear at high dosage because dispersion defects and air entrapment can offset fibre efficiency. In ECC mixtures designed with high-modulus Kuraray PVA fibre at 2 vol%, published laboratory work reports tensile strain capacity above 3% and multiple microcracking. This deflection-hardening response is not obtained with polypropylene macrofibres at equivalent dosage because lower modulus and hydrophobic pull-out behaviour lead to wider cracks and lower stress transfer. Under EN 14651, the limit of proportionality and residual flexural tensile strengths are determined using a notched beam; specification writers should not directly compare ASTM C1609/C1609M residual values with EN 14651 residual values because the test geometries and notch conditions differ. For CE-marked or ASTM-specified fibre use, the manufacturer’s initial type testing under EN 14889-2:2006 includes tensile strength, alkali resistance, and influence on concrete consistency and strength. For thin-shell precast elements and sprayed concrete, RMS702 may require dosage reduction or spray nozzle diameter adjustment when fibre volume fractions exceed 0.5 vol%. The fibre is not intended for primary flexural or shear reinforcement in structural members unless validated by large-scale structural testing and accepted by the responsible design code. In slabs on grade, fibre addition controls plastic settlement and drying shrinkage cracking but does not remove the need for joint layout, curing, and subgrade preparation. The product should not be combined with hydrophobic surface treatments that prevent fibre wetting, because such treatments reduce chemical bond and pull-out resistance. For steam-cured or autoclaved products, trial batches should verify that the curing cycle does not alter fibre–matrix bond. Published RMS702-specific independent data remains limited; therefore batching procedures, admixture compatibility, and hardened-concrete performance should be validated on the project mix design before full-scale placement.